Browning Hi Power
SFS Safety Fast
Shooting Kit For Browning Hi-PowerThe Browning Hi-Power S.F.S. kit can be installed in the new MK III Browning Hi-Power or the pre MK III Browning Hi-Power and the various clones. When installed in a MK III Browning Hi-Power, the S.F.S. kit retains the firing pin lockout system. The S.F.S. system does not eliminate the magazine disconnect on the Browning Hi-Power. With the three safeties activated the S.F.S. allows the hammer to be cocked, and the safeties are then deactivated by simply pressing the ambidextrous safety lever with the thumb. The trigger pull remains light and accurate, allowing a very fast first shot.
$149.95
$162.95
Hardchrome
This safely allows either the right or left handed shooter to safely engage or disengage the safety. A must for combat shooting where weak hand shooting is required.
Hardchrome
BUY
$88.75
BUY
This safely allows the right handed shooter to safely engage or disengage the safety with the thumb of the shooting hand. A must for duty/carry guns.
Hardchrome
BUY
$52.25
BUY
Hardchrome
BUY
$67.50
BUY
different styles of Browning hammers. The size of the ring has been reduced to be the same as on a Colt Commander hammer and has been raised as high as possible. This eliminates hammer bite for most people. Our hammer has been fully machined from 4140 steel and hardened to 47 Rockwell. This hammer meets or exceeds factory specifications. Please do not be fooled by other products on the market. This hammer is manufactured only by Cylinder & Slide, Inc. If you wish to have the hammer installed by our shop we will be happy to do it for you. Please see the Browning Hi-Power Cusom Tuning list for price. The installation of our hammer absolutely does not take the place of a trigger job.
Hardchrome
BUY
$65.00
BUY
This Commander style hammer for the Browning Hi Power is a combination of the best design features from 3 different styles of Browning hammers. The size of the ring has been reduced to be the same size as on a Colt Commander hammer and has been raised as high as possible. This eliminates hammer bite for most people. Our hammer has been fully machined from 4140 steel and hardened to 47 Rockwell. This hammer meets or exceeds factory specifications. Please do not be fooled by other products on the market. This hammer is manufactured only by Cylinder & Slide, Inc. If you wish to have the hammer installed by our shop, we will be happy to do it for you. Please see the Browning Hi Power Custom Tuning list for price. The installation of our hammer absolutely does not take the place of a trigger job.
Hardchrome
BUY $71.00
BUY
The Browning Hi-Power No Bite Chamfered Hammer is specifically designed to reduce the possibility of the hammer hitting or pinching the web of your hand. The edges of the hammer are chamfered for comfortable non-snag carry. The Browning Hi-Power No Bite Chamfered Hammer is made from our Special Tool Steel and heat treated to RC 50-53. All Browning Hi-Power No Bite Chamfered Hammers are 100% inspected and checked for proper RC hardness.
Hardchrome
BUY
$62.50
BUY
The Browning Hi-Power Commander Chamfered Hammer and CNC Machined sear 2 piece set contains our No Bite Hammer and CNC Machined Sear. Both Parts are manufactured from our Special Tool Steel and heat treated to RC 50-53. Each Part is 100% inspected and checked for proper RC hardness.
Hardchrome
BUY
$109.45
BUY
The Browning Hi-Power No bite Chamfered Hammer and CNC Machined sear 2 piece set contains our No Bite Hammer and CNC Machined Sear. Both Parts are manufactured from our Special Tool Steel and heat treated to RC 50-53. Each Part is 100% inspected and checked for proper RC hardness.
Hardchrome
BUY
$109.45
BUY
The Browning Hi-Power Type II Chamfered Commander Hammer and CNC Machined sear 2 piece set contains our No Bite Hammer and CNC Machined Sear. Both Parts are manufactured from our Special Tool Steel and heat treated to RC 50-53. Each Part is 100% inspected and checked for proper RC hardness.
Hardchrome
BUY
$118.80
BUY
Cut from tool steel plate stock by CNC wire EDM and finish machined on CNC machines for exacting tolerances. Heat treated to RC 48-52. Outlasts the cast factory sear thousands of rounds and will produce a clean, crisp trigger pull when properly fitted. It is highly recommended that our commander hammer be used with this sear to produce the best trigger pull.
BUY
CNC machined from the correct spring steel alloy called out in the original specifications for the Browning Hi Power and heat treated for maximum life expectancy. This extractor will allow you to replace the internal style extractor found on early Browning and the Canadian Englis Hi Power pistols. Some fitting of the rear of the extractor may be required as to length as we have made the rear length long enough to accommodate all slides that we have been able to measure.
BUY
BUY
C&S Browning Hi Power Recoil Spring Tool will allow you to remove and replace the recoil spring guide and recoil spring easier and with more safety, especially on the 40 S&W model. The tool is manufactured from unbreakable Deirin and will last a lifetime. This tool comes with complete instructions.
BUY
Installation of this accessory requires drilling and tapping a 6 x 40 hole.
Hardchrome
BUY
$65.00
BUY
This extended slide release allows the shooter to release the slide with the thumb of the shooting hand without shifting his grip.
Hardchrome
BUY
$34.50
BUY
This extra power trigger return spring replaces the MKIII light weight trigger return spring and all older model trigger return springs. The ewtra power wil give you a more positive trigger return for tactical carry pistols.
BUY
Reduces trigger Pull Approximately 1.5 - 2 lbs. Some fitting required.
BUY
Cut from tool steel plate stock by CNC wire EDM and finish machined on CNC machines for exacting tolerances. Heat treated to RC 48-52. Outlasts the cast factory sear thousands of rounds and will produce a clean, crisp trigger pull when properly fitted. It is highly recommended that our commander hammer be used with this sear to produce the best trigger pull.
BUY
The installation of this mag well funnel will give you the largest mag well opening possible. The installation of this part does not increase the length of the frame as 1/4 inch must be trimmed from the mag well opening before installation. Professional installation is required.
BUY
BUY
BUY
10 Round MecGar Browning HP Magazine.
BUY
10 Round MecGar Browning HP Magazine.
BUY
Custom made front sight to fit the factory dovetail. Blade width is .125''. Blade height is .300''. Dovetail dimension is .300 x .80 x 65 degrees. Blue finish.
BUY
Mag Bumper Kit for Browning Hi Power.
BUY
This kit provides the same hammer and firing pin springs as the 25C tac/carry kit with the addition of and extra power trigger return spring. The newer MKIII browning Hi Powers have a reduced power trigger return spring that is unnecessary on a carry pistol. This kit reduces the trigger pull approximately 1.5 lb. Contains 3 Springs.
BUY
These spring kits for your Browning will reduce the trigger pull approximately 2.5 lbs. Contains 2 springs.
BUY
These spring kits for your Browning will reduce the trigger pull approximately 2.5 lbs. Contains all three springs.
BUY
These spring kits for your Browning will reduce the trigger pull approximately 2.5 lbs. Contains 2 springs.
BUY
The wide combat trigger distributes the weight of the trigger pull over a larger area of the finger, making the felt pull less as well as improving trigger control. This trigger eliminates the magazine disconnector.
Hardchrome
BUY
$52.25
BUY